NR120AQM
Main features are as follows.
1) Quad beams detection
Four (4) synchronized pulsed infared beams ensure ultimate stability in any applications.
They eliminate false alarms by small animals, falling leaves, insects and other small subjects.
2) Stacking units.
Up to 4 units stacking is allowed.
3) HD AND mode
When stacking units, upper and lower units can make AND fuature. And it makes higher density protection zone than before.
4) AND / OR mode selection
AND : When Four (4) beams are blocked simultaneously, Alarm is activated.
OR : When either of upper 2 beams OR lower 2 beams are blocked, Alarm is activated.
OR mode protect from the intruder craws through the lowest beams. Maximum 200m outdoor and 400m indoor are available.
5) Double modulated beams
Double modulated beams eliminate influence of External light and Electro Magnetic Interference
6) EDC (Environmental Discrimination Circuit)
When the beam reception level is severely dropped in heavy fog, snow or rain, they often cause unwanted alarm activations.
In case of such conditions, environmental trouble signal is output to distinguish from intrusion. EDC gives additional stability in harsh environment.
7) 100 times sensitivity allowance
Stable operation is maintained even if 99% of beam energy is lost by fog, snow, frost, insect and etc
8) Easy optical alignment
Three alignment methods are available and they achieve easy and quick installation.
Scope, LED, Volt meter
9) High IP rate
IP66 is achieved and protect inside of housing from rain, snow, dust, ect.
10) No blocking sheet
When upper or lower beams are aligned, it is not necessary to cover other beams by the blocking sheet.
11) More features for stable operation.
1) Quad beam detector is more reliable than Dual beam detector.
It is recommended for Important facility , e.g. Airport, Seaport, Plant, Factory, Millitary base, ect.
2) Long distance application.
3) Stacking application.
Model | NR60AQS | NR120AQS | NR200AQS | NR60AQM | NR120AQM | NR200AQM | ||
Power | Input voltage | DC10.5V ~ 28V | ||||||
Current draw | 90mA | 95mA | 100mA | 120mA | 124mA | 128mA | ||
Temp & humid | Operation temp & humid | -25℃~+60℃ RH95% or less | ||||||
Storage temp & humid | -30℃~+70℃ RH95% or less | |||||||
Beam | Detection range outdoor Available for both AND / OR mode |
60m | 120m | 200m | 60m | 120m | 200m | |
Maximum arrival distance Available for both AND / OR mode |
600m | 1200m | 2000m | 600m | 1200m | 2000m | ||
Frequency selection | 1ch | 2 Group x 4 Channels | ||||||
Sensitivity allowance at outdoor range | 100 times | |||||||
Beam modulation | Dual Modulation | |||||||
Interruption time | 40~500msec | |||||||
Optical module | Horizontal : ±90゜/ Vertical : ±10゜ | |||||||
Auto gain control | Available | |||||||
Output | Alarm output | Form | Form 1c (Non-voltage contact) | |||||
Period | 2 Seconds | |||||||
Contact capacity | DC30V, 0.2A (Resistor load) | |||||||
Registor | 3.0Ω or less | |||||||
Tamper output | Form | Form 1b (Non-voltage contact) | ||||||
Period | Open when Cover is open | |||||||
Contact capacity | DC30V, 0.1A (Resistor load) | |||||||
Resistor | 3.0Ω or less | |||||||
EDC output |
Form | Form 1b (Non-voltage contact) | ||||||
Period | Open when EDC is working | |||||||
Contact capacity | DC30V, 0.2A (Resistor load) | |||||||
Resistor | 3.0Ω or less | |||||||
Mechanical structure |
Mount | Wall or pole (φ38mm~φ42.7mm) | ||||||
IP rate | IP66 | |||||||
Dimention | W103xH398xD99 | |||||||
Weight | Tx: 1.2kg Rx: 1.2kg | |||||||
Color | Black / Munsell N1.0 |